| Item | Part No. | Part Name | Qty | Serial No. |
| 423-960-A040 | SEAT ASSEMBLY, COMPRESSED AIRRIDE - 555 | | A31001-UP- |
| 421-960-A210 | KIT, UPPER ASSEMBLY - CHARCOAL FABRIC | | A31001-UP- |
| 1 | 195-57-A0200 | KIT, FRAME ASSEMBLY | | A31001-UP- |
| 2 | 421-960-A360 | KIT, HANDLE | | A31001-UP- |
| 3 | 195-57-A0220 | KIT, LUMBAR SUPPORT | | A31001-UP- |
| 4 | 195-57-A0300 | KIT, BACK FOAM | | A31001-UP- |
| 5 | 421-960-A220 | KIT, BACK COVER - CHARCOAL FABRIC | | A31001-UP- |
| 6 | 195-57-A0500 | KIT, SEAT FOAM | | A31001-UP- |
| 7 | 195-57-A0400 | KIT, SEAT COVER - CHARCOAL FABRIC | | A31001-UP- |
| 8 | 195-57-A0800 | KIT, HEIGHT RISER ASSEMBLY | | A31001-UP- |
| 9 | 195-57-A0900 | KIT, HEIGHT RISER LATCH | | A31001-UP- |
| 10 | 195-57-A0010 | KIT, HEIGHT RISER SPRING | | A31001-UP- |
| 11 | 206-57-A1470 | KIT, RECLINER CABLE | | A31001-UP- |
| 12 | 421-960-A310 | KIT, DAMPER | | A31001-UP- |
| 13 | 421-960-A450 | KIT, 24 V COMPRESSOR SUSPENSION ASSEMBLY | | A31001-UP- |
| 14 | 421-960-A350 | KIT, SLIDERAIL | | A31001-UP- |
| 15 | 195-57-A0310 | KIT, UPSTOP/BUMP STOP | | A31001-UP- |
| 16 | 421-960-A460 | KIT, AIR SPRING | | A31001-UP- |
| 17 | 421-960-A470 | KIT, SUSPENSION COVER | | A31001-UP- |
| 18 | 421-960-A480 | KIT, 24 V COMPRESSOR/VALVE | | A31001-UP- |
| 19 | 421-960-A490 | KIT, BEARING | | A31001-UP- |
| 20 | 421-960-A510 | KIT, LEVER/CENTER PIVOT | | A31001-UP- |
| 21 | 421-960-A430 | KIT, L.H. ARMREST | | A31001-UP- |
| 421-960-A440 | KIT, R.H. ARMREST | | A31001-UP- |
| 22 | | BRACKET, L.H. (SEE FIG. K0110-01A0) | | A31001-UP- |
| 23 | | BRACKET, R.H. (SEE FIG. K0110-01A0) | | A31001-UP- |
| 24 | | BOLT (SEE FIG. K0110-01A0) | | A31001-UP- |
| 25 | | SCREW (SEE FIG. K0110-01A0) | | A31001-UP- |
| 26 | 419-06-A2210 | HARNESS, WIRING | | A31001-UP- |
| N/I | 08037-01008 | GROMMET | | A31001-UP- |
| N/I | 08022-04001 | CONNECTOR | | A31001-UP- |
| N/I | 08021-00400 | CONNECTOR | | A31001-UP- |
| | | | |
| | F1 - REPLACEMENT OF CENTER PIVOT BEARINGS REQUIRES REPLACEMENT OF ITEM 18. | | |
| | | | |
| | F2 - THIS KIT IS REQUIRED TO SERVICE THE CENTER PIVOT BEARING ON UNITWITH WELDED PIVOT PINS. | | |
| | | | |
