| Item | Part No. | Part Name | Qty | Serial No. |
| 1 | | CYLINDER, RIPPER (FIG. H5200-01A13) | | |
| 2 | 116 436 | CAP, BALL | | |
| 3 | 116 358 | SHIM 0.040 | | |
| 116 359 | SHIM 0.002 | | |
| 116 360 | SHIM 0.003 | | |
| 116 361 | SHIM 0.005 | | |
| 4 | 25 515 R1 | BOLT | | |
| 5 | 26 068 R1 | WASHER, FLAT | | |
| 6 | 109 454 | FITTING, GREASE | | |
| 7 | 152 843 | LINK, UPPER | | |
| 8 | 1261 201 H91 | LINK, LOWER | | |
| 1260 195 H1 | BUSHING, SPLIT | | |
| 9 | 1261 669 H92 | MOUNT, RIPPER | | |
| 10 | 24 892 R1 | BOLT | | |
| 11 | 26 068 R1 | WASHER, FLAT | | |
| 12 | 26 068 R1 | WASHER, FLAT | | |
| 13 | 25 529 R1 | NUT, HEX | | |
| 14 | 1261 670 H91 | BEAM, RIPPER - 1/4 IN. BOLT (WITHOUT REAR HITCH) | | |
| 1261 670 H92 | BEAM, RIPPER - 3/8 IN. BOLT (WITHOUT REAR HITCH) | | |
| 1261 670 H93 | BEAM, RIPPER - WITH REAR HITCH | | |
| 15 | 1259 029 H1 | PIN - FOR 1/4 IN. BOLT | | |
| 1259 029 H2 | PIN - FOR 3/8 IN. BOLT | | |
| 16 | 26 285 R1 | BOLT - 1/4 IN. | | |
| 25 500 R1 | BOLT - 3/8 IN. | | |
| 17 | 26 110 R1 | NUT, LOCK - USE WITH 1/4 IN. BOLTS | | |
| 9413 979 | NUT, LOCK - USE WITH 3/8 IN. BOLTS | | |
| 18 | 154 239 | SHANK, RIPPER | | |
| 19 | 154 243 | BUSHING, RIPPER FRONT | | |
| 20 | 154 244 | PIN, RIPPER POINT | | |
| 21 | 154 242 | POINT, RIPPER | | |
| 22 | 1433 073 H1 | LANYARD | | |
| 23 | 25 489 R1 | BOLT | | |
| 25 532 R1 | WASHER, FLAT | | |
| 25 519 R1 | NUT | | |
| 24 | 25 752 R1 | BOLT | | |
| 25 532 R1 | WASHER, FLAT | | |
| 25 | 455 238 R1 | PIN, ROLL | | |
| 26 | 1432 695 H1 | PIN, HITCH | | |
| 27 | 1433 035 H1 | PIN, SELF-LOCKING | | |
| 28 | 154 659 | TEETH, SCARAFIER | | |
| 29 | 1280 985 H1 | SHANK | | |
| 30 | 1266 753 H1 | TOOTH | | |
| 1440 304 H91 | KEY - SHANK WITH RUBBER INSERT | | |
| 31 | 46 475 A | KEY | | |
| 32 | 1438 588 H1 | INSERT, RUBBER | | |
| | | | |
| | F1 WHEN USING THE SCARAFIER TEETH FOR LIGHT RIPPING, DO NOT MIX THE RIPPER TEETH AND SHANKS WITH SCARAFIER TEETH AND SHANKS | | |
| | | | |
