| Item | Part No. | Part Name | Qty | Serial No. |
| 1 | 24 895 H1 | BOLT - TIGHTEN TO 355 FT/LBS WET | | |
| 2 | 25 913 R1 | NUT, HEX - TIGHTEN TO 160 FT/LBS WET | | |
| 3 | 1284 739 H2 | SCREW, SET | | |
| 4 | 26 068 R1 | WASHER, FLAT | | |
| 5 | 1284 670 H91 | BRACKET WELDMENT - L.H | | |
| 22 902 | STUD, BALL | | |
| 6 | 1284 664 H1 | PLATE, BACKING | | |
| 7 | 1284 663 H2 | WEAR PAD | | |
| 8 | 1284 665 H2 | SPACER, DOVETAIL | | |
| 9 | 1284 672 H1 | BAR, TIE | | |
| 10 | 26 309 R1 | BOLT | | |
| 11 | 25 534 R1 | WASHER, FLAT | | |
| 12 | 1285 528 H1 | GUARD, MOLDBOARD SHIFT CYLINDER | | |
| 13 | 109 461 | FITTING, GREASE | | |
| 14 | 343 909 R1 | O-RING | | |
| 15 | 384 251 R1 | O-RING | | |
| 16 | 219 778 | NUT, JAM - TIGHTEN OUTER NUT TO 350 FT/LBS WET | | |
| 17 | 1287 767 H1 | PLATE, SEAL RETAINER | | |
| 18 | 1284 770 H1 | BUSHING | | |
| 19 | 1287 766 H1 | PIN, TAPER | | |
| 20 | 26 297 R1 | WASHER, FLAT | | |
| 21 | 103 410 | PIN, COTTER | | |
| 22 | 25 893 R1 | NUT, SLOTTED HEX | | |
| 23 | 51 493 | NUT, LOCK - TIGHTEN TO 225 FT/LBS WET | | |
| 24 | 592 993 R1 | SPACER | | |
| 25 | 26 665 R1 | WASHER, FLAT | | |
| 26 | 28 121 R1 | BOLT | | |
| 27 | | CYLINDER, MOLDBOARD SHIFT (SEE PG 10-198) | | |
| 28 | | CYLINDER, MOLDBOARD TILT (SEE PG 10-200) | | |
| 29 | 1284 671 H91 | BRACKET WELDMENT - R.H | | |
| 30 | 22 902 | STUD, BALL | | |
| 31 | 9412 231 | NUT, LOCK | | |
| 32 | 38 616 | CAP, BALL | | |
| 13 953 A | SHIM | | |
| 13 953 B | SHIM | | |
| 33 | 24 876 R1 | BOLT | | |
| 34 | 1285 473 H1 | BUSHING, MOLDBOARD SLIDE | | |
| 35 | 25 553 R1 | WASHER, FLAT | | |
| 36 | 24 840 R1 | BOLT | | |
| 37 | 1286 099 H1 | PIN | | |
| 103 410 | PIN, COTTER | | |
| 38 | | MOLDBOARD (SEE PG 17-026) | | |
| 39 | 139 993 | MOUNT WELDMENT | | |
| 40 | 25 918 R1 | BOLT | | |
| 1285 859 H1 | NUT, LOCK - THIGHTEN TO 100 FT/LBS WET | | |
